Cisco 300-110 Practice Exam Questions

Cisco 300-110 Sample Question Answers

Question # 1

An engineer is conducting a Layer 2 site survey. Which type of client must the engineer match to the survey? 

A. best client available 
B. phone client 
C. normal client 
D. worst client available 

Show Answer

Question # 2

An enterprise network is deploying two Cisco Catalyst 9800 WLCs in a data center to ensure uninterrupted wireless services for a campus with thousands of users. The IT management requests a design that enables seamless failover without client reauthentication or loss of connectivity if one controller fails. Ease of configuration and ongoing management are high priorities. The controllers will be connected via a high-speed LAN segment, and both must support full active-passive redundancy for all managed APs. Which design approach meets the requirements? 

A. Configure the 9800 WLCs in separate mobility groups and synchronize configurations manually. 
B. Implement SSO with redundancy management interface and AP SSO enabled between the two controllers. 
C. Deploy the controllers with VRRP to provide gateway redundancy and manually synchronize WLAN profiles. 
D. Enable N+1 redundancy, assigning primary and secondary controllers to each AP, and use DHCP for failover. 

Show Answer

Question # 3

A company is upgrading its wireless infrastructure and is in a state of transition. Some parts of the company's building still run on the legacy WLC. The new WLC is not located at the same site as the legacy WLC. The company requires seamless client inter-controller roaming between the new WLC and the legacy WLC, with no disruptions. Both WLCs are separated by firewalls. Which troubleshooting command validates that the mobility control packets between the WLCs can be sent and received? 

A. mapping mobility_peer IP address 
B. debug mobility handoff enable 
C. debug mobility config enable 
D. mapping mobility_peer_management IP address 

Show Answer

Question # 4

A customer has a single anchor WLC named Anchor A. Anchor A is in a DMZ and provides guest access. The customer wants to deploy an additional anchor controller named Anchor B to provide redundancy if Anchor A fails. Which design approach should be taken for the guest WLAN priority on the foreign WLC for each anchor WLC?

 A. Set Anchor A to priority 3 and Anchor B to priority 3. 
B. Set Anchor A to priority 3 and Anchor B to priority 1. 
C. Set Anchor A to priority 1 and Anchor B to priority 1. 
D. Set Anchor A to priority 1 and Anchor B to priority 3. 

Show Answer

Question # 5

An engineer configured the optimized client roaming on Cisco WLC with an RSSI threshold of -72 dBm. Clients report frequent disconnections. What must be configured for the AP to guide the client to a better AP? 

A. Enable BSS transition on the SSID and optimized roaming at the radio level. 
B. Disable coverage hole detection on the SSID and enable BSS transition on the SSID. 
C. Enable BSS transition at the radio level and optimized roaming on the SSID. 
D. Disable optimized roaming and enable 802.11v support on the SSID. 

Show Answer

Question # 6

A customer has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity. 5 access points are set to high failover priority and 7 access points are set to critical failover priority. During a failure, not all critical access points failed over to the backup Cisco WLC. Which configuration is the cause of this issue? 

A. The high priority access point is oversubscribed. 
B. network ap-priority is set to enable. 
C. The critical priority access point count is oversubscribed. 
D. network ap-priority is set to disable. 

Show Answer

Question # 7

A wireless engineer is preparing for a meeting with a customer to discuss a new wireless network design. The customer is a company that develops code and occupies a three-story building. Which two information points does a pre-site survey questionnaire contain? (Choose two.)

A. total number of access points in use 
B. client devices that will connect to the wireless network 
C. access point density required 
D. model of the wireless controller 
E. applications that will run over the wireless network 

Show Answer

Question # 8

A customer has two Cisco Catalyst 9800 Series WLCs named WLC-A and WLC-B in an N+1 configuration with the same WLANs but different Layer 3 interfaces for each WLC, and APs in local mode. WLC-A manages Building A APs and WLC-B manages Building B APs. The customer wants users to remain connected and retain their session state including the IP address when moving between buildings. How must this requirement be incorporated into the design? 

A. Create a mobility tunnel between WLC-A and WLC-B with the same group name. 
B. Configure WLC-A and WLC-B in a high-availability cluster and set a mobility MAC address. 
C. Implement AP groups for each building by using the same name on WLC-A and WLC-B. 
D. Connect WLC-A and WLC-B by using the redundancy port to sync client sessions. 

Show Answer

Question # 9

An engineer must design AP placements for a new branch office that contains two floors. The engineer uses Ekahau to complete the predictive survey. To calculate the signal bleed through between floors, the engineer creates a building, adds the floors, and attenuation areas. After the scale is set, what else must be added on the floors to accurately measure the signal bleed at a specific location? 

A. Draw in coverage areas. 
B. Start the auto planner. 
C. Add alignment points. 
D. Choose the access point models.

Show Answer

Question # 10

Which strategies must the engineer use for the antenna deployment model in a warehouse? 

A. ceiling-mounted, directional antennas 
B. wall-mounted, low-gain, omnidirectional antennas 
C. ceiling-mounted, high-gain, omnidirectional antennas 
D. wall-mounted, patch directional antennas 

Show Answer